Leatherman Replacement Wire Cutter Kit
Worn wire cutters? Replace the cutters, not the tool.
Leatherman's Replacement Wire Cutter Kit restores your pliers' cutting edges in a few minutes at home. You get a fresh set of premium stainless steel cutter inserts, new screws and the Torx #8 key to fit them. It works with the ARC, Wave Alpha, Wave+, Surge, Signal, Rebar and Super Tool 300, and comes in silver or black to match your tool.
In the kit: Inserts, screws, key
Material: Stainless steel
Fitting time : A few minutes
Tool needed : Torx #8, included
Colours : Silver, black
Made by : Leatherman, USA
Why buy your cutter kit from LightMen
-
Genuine Leatherman parts
Original Leatherman inserts, hard to find in India and made to fit your tool exactly.
-
Ships in 1 business day
Dispatched from our Hyderabad warehouse. Orders before 11 am ship the same day.
-
GST invoice
18% GST is included in the price. Registered businesses can claim input tax credit.
-
Help fitting them
Stuck? Message us on WhatsApp and we'll walk you through it.
-
See it before you buy
Visit our Hyderabad store, or book a video call demo from anywhere in India.
When is it time to replace them?
Wire cutters wear with use, especially on hard or steel wire. If you notice any of these, a new set will make your pliers cut like new.
-
Wire won't cut cleanly
You have to squeeze harder, or the wire bends and crushes instead of snipping.
-
Nicks or chips on the edge
Cutting hard steel wire can chip the cutting edge, leaving gaps.
-
Light shows through
Close the pliers and hold them up to the light. A gap between the cutters means they've worn.
-
Thin wire slips through
Fine wire and strands slide between the edges instead of being cut.
In the kit
- 1 set of replacement wire cutter inserts
- 2 screws
- 1 Torx #8 key for fitting (key colour may vary)
Why replace instead of buying new?
The cutters are usually the first part of a Leatherman to wear. Swapping the inserts brings your pliers back to full cutting power for a fraction of the cost of a new tool, and keeps the tool you know and trust.
Choose the colour that matches your tool
Both colours are the same part, so they fit and cut identically. Pick the one that matches your tool's finish. Choose yours from the options above.
Silver
For stainless steel tools: Wave+, Surge, Rebar and Super Tool 300 in stainless, and the Signal.
Black
For black-finish tools: Wave+, Surge, Rebar and Super Tool 300 in black, the Wave Alpha and the ARC.
Fits these Leatherman tools
The kit fits Leatherman tools with replaceable wire cutters. Tap a tool to view it.
Also fits the Leatherman MUT, Knifeless Rebar, Super Tool 300M and Batch #005 (40th Anniversary Tool). Not sure about your tool? Message us its name and we'll confirm.
How to replace your wire cutters
It takes a few minutes and needs only the Torx #8 key in the kit. Work on a table or tray so the small screws don't roll away.
-
Open the pliers
Open the pliers fully so you can see the cutter inserts and their screws near the jaw pivot.
-
Remove the old screws
Use the Torx #8 key to undo the screw holding each old cutter insert.
-
Swap the inserts
Lift out the worn inserts and seat the new ones in the same position and orientation.
-
Fit the new screws
Use the new screws from the kit. Tighten them firmly, but don't over-tighten.
-
Test a cut
Close the pliers to check the edges meet cleanly, then snip a piece of wire.
Before removing the old inserts, take a quick photo with your phone so you can match the new ones exactly. Need help? Message us on WhatsApp.
Specifications
| Contents | 1 set of cutter inserts, 2 screws, 1 Torx #8 key |
|---|---|
| Insert material | Premium stainless steel |
| Colours | Silver, black |
| Brand | Leatherman, Portland, Oregon, USA |
| Fits | ARC, Wave Alpha, Wave+, Surge, Signal, Rebar, Super Tool 300 |
|---|---|
| Also fits | MUT, Knifeless Rebar, Super Tool 300M, Batch #005 |
Questions customers ask us
Will it fit my Leatherman?
It fits the ARC, Wave Alpha, Wave+, Surge, Signal, Rebar, Super Tool 300, MUT, Knifeless Rebar, Super Tool 300M and Batch #005. If your tool isn't listed, message us its name and we'll confirm before you order.
Silver or black: which should I choose?
Both cut identically. Choose silver for stainless steel tools and black for black-finish tools, so the cutters match the look of your Leatherman.
Do I need any special tools to fit them?
No. The Torx #8 key you need is included in the kit, along with new screws.
Can I fit them myself?
Yes. It takes a few minutes with the included key. Follow the steps above, and message us if you get stuck.
How quickly will it reach me?
We ship from Hyderabad within one business day, and orders placed before 11 am ship the same day. Delivery time after that depends on your city.
Will I get a GST invoice?
Yes. The price includes 18% GST, and registered businesses can claim input tax credit. Share your GSTIN when you order.
Legal declaration
- Common generic name
- Replacement wire cutter inserts
- Brand and model
- Leatherman Replacement Wire Cutter Kit
- Net quantity
- 1 set (cutter inserts, 2 screws and 1 Torx #8 key)
- MRP
- ₹1,290 (inclusive of all taxes)
- Country of origin
- USA
- Manufacturer
- Leatherman Tool Group, Inc., Portland, Oregon, USA
- Imported and marketed by
- EAS, Pune
- Month and year of import
- Printed on the pack
- Consumer care
- LightMen, Hyderabad, Telangana. Phone +91-98490 00777, email sales@lightmen.in
Pictures are for illustration only. The actual product may vary slightly.
We ship from our Wear-house in Hyderabad within 24 hours of order receipt.
Orders received before 11am are shipped the same day.
You may also like...
More from Leatherman Tools in India
Recently viewed